5 Best Replacement Filters for Santa Fe Dehumidifiers (November 2026)
The best Santa Fe dehumidifier filters include the Santa Fe Certified MERV 13 Dehumidifier Filter for broad Santa Fe compatibility, the CPLIKE MERV 13 Dehumidifier Filter 14 x for four-filter value, and the QUNYI Filter for Santa Fe Force Dehumidifier for Force and Advance 2 owners.
On this page (5 sections)
The best Santa Fe dehumidifier filters are the Santa Fe Certified MERV 13 and CPLIKE MERV 13 options, provided your unit uses the 14 x 17.5 x 1.75 in size. Force and Advance 2 owners also have MERV 8 choices, while the Dri-Eaz pick is only for a PHD200 unit.
Filter fit matters as much as the MERV rating. A filter that is close in size can still leave gaps or fail to sit in the slot as intended.
That is why the model check comes before the rating check in this guide.
If you are replacing a filter in a crawl space, see crawl space dehumidifier filters. The same basic rule applies there, because airflow depends on a clean and correct fit.
Compare the dimensions printed on your current filter with the replacement, then confirm the dehumidifier model before ordering. Write down the length, width and thickness so you can compare them in the same order.
If you need a higher-rated option, see our guide to best santa fe dehumidifier filters merv 13. For cleaning instructions before replacement, read How to Clean a Dehumidifier Filter?.
The picks below suit different needs, from a single named Santa Fe replacement to a four-pack for regular maintenance. Use the section that matches your model first, and treat the other options as alternatives only when the size and compatibility line up.
Our picks at a glance
-
1
Best for broad Santa Fe compatibilitySanta Fe Certified MERV 13 Dehumidifier Filter
9.7/10 our score
See it on Amazon -
2
Best for four-filter valueCPLIKE MERV 13 Dehumidifier Filter 14 x
9.7/10 our score
See it on Amazon -
3
Best for Force and Advance 2 ownersQUNYI Filter for Santa Fe Force Dehumidifier
9.3/10 our score
See it on Amazon
- 4
Check itSanta Fe MERV 8 Dehumidifier Filter
Best for a standard 4031062 replacement - 5
Check itDri-Eaz F527 Polyester Mesh Filters for PHD
Best for Dri-Eaz PHD 200 units
The best Santa Fe dehumidifier filters by use
The Santa Fe Certified filter is the broadest Santa Fe match here, while CPLIKE offers the same stated 14 x 17.5 x 1.75 in size in a 4-pack. The remaining choices are better for specific models, ratings or equipment.
Santa Fe Certified MERV 13 Dehumidifier Filter: Best for broad Santa Fe compatibility
- 14 x 17.5 x 1.75 in
- MERV 13
- Pleated paper construction
- 1-count pack
This Santa Fe filter combines a MERV 13 rating with compatibility across several Advance, Force and Ultra models. Its 1-count format suits a buyer replacing one filter at a time.
Pros
- Broad Santa Fe model compatibility
- MERV 13 filtration
- Pleated construction
Cons
- Only 1 filter in the pack
- Compatibility still depends on the exact model
The Santa Fe Certified MERV 13 Dehumidifier Filter is the best starting point for owners who want a named Santa Fe replacement with broad compatibility. It fits the stated 14 x 17.5 x 1.75 in dimensions and works with the Advance2, Force, Advance90, Advance100, Advance120, Ultra98H and Ultra120H models.
Its MERV 13 rating gives it a higher filtration rating than the MERV 8 choices in this guide. The pleated paper construction uses a rectangular filter shape, and the package contains 1 filter.
This pick makes the most sense when you want one replacement for a compatible Santa Fe unit and don't need a multi-pack. The single-filter format also makes it easier to match one scheduled replacement to one unit.
Pleated construction spreads the filtering media across more surface area than a flat sheet. In daily use, that design helps the filter collect particles while keeping the airflow path open for longer between checks.
The paper material and box frame construction are made for a standard residential dehumidifier slot. You should still check that the frame sits flat and that the filter does not bow or press against the housing.
Check the model number and the filter slot before ordering. The shared 14 x 17.5 x 1.75 in dimensions are useful, but model compatibility remains the deciding check.
CPLIKE MERV 13 Dehumidifier Filter 14 x: Best for four-filter value
- 14 x 17.5 x 1.75 in
- MERV 13
- 4-pack
- Fiberglass and polyester material
The CPLIKE filter uses the same stated dimensions as the Santa Fe MERV 13 pick and comes in a 4-pack. Its wider compatibility list also includes Honeywell DR90 and DR120 models.
Pros
- 4-pack format
- MERV 13 rating
- Includes fiberglass and polyester material
Cons
- Exact fit should be checked against the unit
- The product name is shortened in the supplied title
The CPLIKE MERV 13 Dehumidifier Filter 14 x is the better fit for buyers who want several replacements ready at once. It has the same stated 14 x 17.5 x 1.75 in dimensions as the Santa Fe Certified option and includes 4 filters.
CPLIKE identifies compatibility with Santa Fe Advance90, Advance100, Advance120, Ultra98H, Ultra120H, Advance2 and Force models. It also identifies Honeywell DR90 and DR120 compatibility, which gives this option a wider stated equipment range than the other 14 x 17.5 x 1.75 in picks.
The filter uses fiberglass and polyester material. Its MERV 13 rating suits shoppers looking for the higher-rated filtration choice in this group, but you should still confirm that your unit accepts this size and rating.
Choose it when a 4-pack is more useful than a single replacement. For a different brand, compare our guide to the best midea dehumidifier filter.
QUNYI Filter for Santa Fe Force Dehumidifier: Best for Force and Advance 2 owners
- 17.5 x 14 x 1.75 in
- MERV 8
- 4-pack
- Disposable fabric filter
This QUNYI 4-pack matches the stated 14 x 17.5 x 1.75 in filter size for Santa Fe Force and Advance 2 dehumidifiers. It is disposable and uses MERV 8 filtration.
Pros
- 4-pack
- Designed for Force and Advance 2
- Disposable replacement format
Cons
- MERV 8 rather than MERV 13
- Narrower model compatibility
The QUNYI Filter for Santa Fe Force Dehumidifier is the most targeted choice for Santa Fe Force and Advance 2 owners who need a 4-pack. Each filter measures 17.5 x 14 x 1.75 in and uses a MERV 8 rating.
The filter is made from fabric and is disposable. The product information identifies it as a replacement for the Santa Fe Force and Advance 2, including the 4031062 part number.
The information also says the pleated fabric filter can generally be vacuumed clean several times before replacement. Follow the condition of the filter and the instructions for your equipment rather than treating a calendar interval as a guarantee.
This is a practical choice when your unit calls for the 1.75 in MERV 8 format and you want four replacements. It is not the right pick for a model that requires the 14 x 17 x 2 in Therma-Stor filter.
Santa Fe MERV 8 Dehumidifier Filter: Best for a standard 4031062 replacement
- 14 x 17 x 2 in
- MERV 8
- Pleated construction
- 1-count pack
This Therma-Stor filter is a standard MERV 8 replacement for Santa Fe Advance2 and Force units. Its 14 x 17 x 2 in dimensions differ from the 1.75 in filters, so measure before ordering.
Pros
- Specific Advance2 and Force compatibility
- Pleated construction
- Standard MERV 8 rating
Cons
- Only 1 filter in the pack
- Different dimensions from several other picks
The Santa Fe MERV 8 Dehumidifier Filter from Therma-Stor is designed for Santa Fe Advance2 and Force units. Its 14 x 17 x 2 in dimensions are different from the 14 x 17.5 x 1.75 in size used by several other filters here.
It has pleated construction, a MERV 8 rating and a 1-count pack. The model number is 4031062, and the manufacturer part number is SYL-1668.
This filter suits buyers replacing a standard filter in a compatible Advance2 or Force unit. The main decision point is the size, because a similar model name does not remove the need to compare the old filter.
The 2 in thickness is a clear difference from the 1.75 in options. That extra quarter inch can matter in a slot that is built for a specific filter depth.
Pleated construction helps maintain surface area as the filter loads with dust. In practice, you should check it on a regular schedule and replace it when airflow begins to drop.
Use the dimensions on your existing filter as the final fit check. Choose this option when the 14 x 17 x 2 in format matches your equipment.
Dri-Eaz F527 Polyester Mesh Filters for PHD: Best for Dri-Eaz PHD 200 units
- Polyester mesh
- 3-pack
- Reusable
- Compatible with PHD200
This Dri-Eaz F527 filter is for the PHD200 dehumidifier rather than the Santa Fe models above. Its polyester mesh construction and reusable format make it a separate choice for PHD200 owners.
Pros
- Reusable filter format
- 3-pack
- Polyester mesh
Cons
- For Dri-Eaz PHD200 only
- Not a Santa Fe replacement
The Dri-Eaz F527 Polyester Mesh Filters are for the Dri-Eaz PHD200 dehumidifier, so they are not a Santa Fe replacement. This distinction matters if you are comparing filters across brands or managing more than one dehumidifier.
The package contains 3 filters made from polyester mesh. The filter is reusable, and the product information identifies the part number as F527.
Choose this option only when your equipment is a PHD200. Its 3-pack format can suit a service closet or maintenance schedule, but it should not be used as a substitute for a Santa Fe filter without confirmed compatibility.
Polyester mesh works differently from the pleated paper and fabric filters used in the Santa Fe options. A mesh design is built to keep larger debris from blocking the airflow path while allowing the filter to be cleaned and reused.
Because the format is reusable, care matters more than it does with a disposable filter. You should follow the equipment instructions for cleaning, and retire a mesh filter if it becomes damaged or no longer holds its shape.
If you're comparing another type of dehumidifier filter, our guide to the best replacement air filter for dehumidifier explains the general fit and material checks.
How to match a Santa Fe filter by dimensions
The safest way to choose a replacement is to match the old filter's length, width and thickness with the new filter. The options here show why the thickness deserves attention: several are 1.75 in thick, while the Therma-Stor option is 2 in thick.
Write down the measurements in the same order every time. A filter described as 14 x 17.5 x 1.75 in should not be treated as identical to one described as 14 x 17 x 2 in.
Length and width set the basic footprint of the filter. When those numbers are swapped or rounded in a listing, the filter may look close but still leave an open edge in the slot.
Thickness controls how the filter seats in the housing. A filter that is too thick can press against the cover, and a filter that is too thin can shift or allow air to pass around the frame.
Also compare the model name. The Santa Fe Certified filter lists seven compatible Santa Fe models, while the QUNYI and Therma-Stor MERV 8 filters focus on Force and Advance2 equipment.
Model compatibility is not just a brand check. Santa Fe uses several model names across its dehumidifier range, and a filter that fits one slot may not be the correct part for another unit.
A correct filter should sit in the intended slot without forcing it. Don't trim, bend or compress a filter to make an uncertain size fit.
Forcing a filter can damage the pleats or the frame, and it can change how air moves through the unit. If the filter does not slide in with normal hand pressure, stop and recheck the measurements.
Keep the old filter until the replacement is fitted and the unit is running. That way you can compare the two side by side and spot a difference in depth or frame shape before you discard the original.
This step takes very little time and prevents the most common replacement mistake. Most fit problems come from ordering by model name alone without confirming the three dimensions on the filter that is already in the unit.
MERV 8 versus MERV 13 for Santa Fe equipment
MERV 13 has a higher filtration rating than MERV 8, but the best rating for your unit is the one that matches its approved filter design. The Santa Fe Certified and CPLIKE options are MERV 13, while QUNYI and Therma-Stor are MERV 8.
A higher rating can be appealing when filtration is your main concern. Still, filter thickness, airflow and model compatibility come first because an unsuitable filter can create a poor fit or restrict normal operation.
Use the MERV rating as one comparison point, not the only one. If your Santa Fe unit calls for a MERV 8 filter, choose the correct MERV 8 size unless the equipment documentation confirms another option.
The MERV rating describes how fine a particle the filter is rated to capture. A higher number generally means finer filtration, but it does not mean the filter will fit every dehumidifier or that the unit was designed for that rating.
Airflow is the other side of that trade-off. A filter that captures more fine particles can load faster, so the unit may need more frequent checks to keep air moving freely.
That is why the slot design matters. The housing, fan and filter depth are set up as a system, and changing the filter type without checking that system can create problems you did not have before.
For many homes, the standard MERV 8 filter is enough for the job the dehumidifier was built to do. It protects the coils and keeps general dust from building up inside the unit.
A MERV 13 filter makes more sense when the unit lists it as compatible and you want that higher rated filtration. In that case, the size and model checks still come first.
Do not use the rating to justify a wrong size. A MERV 13 filter in the wrong dimensions will not perform as intended, no matter how strong the rating looks on the box.
Compare rating, dimensions and model together. When all three line up, you can choose the filter with confidence instead of guessing based on one number.
How to replace and care for a dehumidifier filter
Turn the dehumidifier off before removing the filter, then compare the replacement with the old one before inserting it. Keep the filter orientation and airflow direction consistent with the markings on the unit or filter.
For reusable or cleanable designs, follow the equipment instructions before vacuuming or washing. The QUNYI information says its pleated fabric filter can generally be vacuumed several times, while the filter itself is described as disposable.
Vacuuming works best as a light maintenance step between replacements. Use a soft brush attachment and gentle pressure so you do not tear the pleats or push dust deeper into the media.
Washing is not suitable for every filter type. Paper and disposable fabric filters should not be soaked unless the equipment instructions say so, because water can damage the media and the frame.
Don't keep using a visibly damaged or heavily loaded filter. Reduced airflow can affect how the equipment operates, so regular checks are useful even when a replacement date has not arrived.
A loaded filter forces the fan to work harder to pull air through the unit. Over time, that can reduce moisture removal and add strain to parts that were designed to run with a clear airflow path.
Check the filter whenever you notice a change in sound, airflow or condensation control. A quick look at the pleats will often tell you whether the filter is still doing its job or has reached the end of its useful life.
Store spare filters in a clean and dry place. Keeping them flat and free of dust helps them stay ready for the next change, especially with multi-pack options.
A carbon filter serves a different purpose from the filters in this roundup. See the best replacement carbon filter for dehumidifier if odor control is the reason you're shopping.
Use the right filter for the right job. Particle filters protect airflow and internal parts, while carbon filters are aimed at odors, and the two should not be treated as interchangeable.
What to choose for your Santa Fe dehumidifier
Choose the Santa Fe Certified MERV 13 if you need broad compatibility across listed Santa Fe Advance, Force and Ultra models. Pick CPLIKE if you want the same stated 14 x 17.5 x 1.75 in format in a 4-pack.
Choose QUNYI for a 4-pack of MERV 8 filters for Santa Fe Force or Advance 2 units when the 1.75 in thickness matches. Pick Therma-Stor when your compatible unit requires the 14 x 17 x 2 in format.
The Dri-Eaz F527 belongs with PHD200 equipment, not Santa Fe dehumidifiers. Confirm the model, dimensions and MERV requirement before ordering any replacement.
Start with your dehumidifier model and the filter already installed. Those two details will narrow the list faster than any rating or pack size, because they confirm that the filter is made for your slot.
If you own a compatible Santa Fe Advance, Force or Ultra unit and want a single named replacement, the Santa Fe Certified option is the simplest choice. Its broad model list covers more of the Santa Fe range than the other picks here.
If you prefer to keep spares on hand, the CPLIKE 4-pack and QUNYI 4-pack both make sense for regular maintenance. A multi-pack is easier to live with when you run the dehumidifier for long periods and want the next filter ready.
For Force and Advance 2 units that call for MERV 8, match the thickness carefully. The QUNYI option uses 1.75 in, while the Therma-Stor option uses 2 in, and that difference should guide the final order.
The Dri-Eaz F527 is a separate choice for PHD200 owners, with a reusable polyester mesh design. It should only be ordered for that equipment, not as a general Santa Fe substitute.
Once you have the right filter, set a simple check schedule and inspect it regularly. A clean and correctly fitted filter keeps airflow steady and helps the dehumidifier do the work it was built to do.
Our top 3 picks at a glance
-
1
Best for broad Santa Fe compatibility
Santa Fe Certified MERV 13 Dehumidifier Filter
9.7/10 our score
See it on Amazon -
2
Best for four-filter value
CPLIKE MERV 13 Dehumidifier Filter 14 x
9.7/10 our score
See it on Amazon -
3
Best for Force and Advance 2 owners
QUNYI Filter for Santa Fe Force Dehumidifier
9.3/10 our score
See it on Amazon
Frequently asked questions
What is the best Santa Fe dehumidifier filter?
The Santa Fe Certified MERV 13 filter is the strongest general choice when your unit is one of its compatible Advance, Force or Ultra models. It measures 14 x 17.5 x 1.75 in and comes as a 1-count filter.
Confirm your model and filter dimensions before ordering.
What size filter fits a Santa Fe dehumidifier?
Several filters in this guide use a 14 x 17.5 x 1.75 in size, including the Santa Fe Certified, CPLIKE and QUNYI options. The Therma-Stor MERV 8 filter measures 14 x 17 x 2 in.
Check the old filter and your unit model because similar names do not guarantee the same fit.
Is MERV 13 better than MERV 8 for a dehumidifier?
MERV 13 provides a higher stated filtration rating than MERV 8, but the correct choice is the one approved for your dehumidifier and filter slot. A higher rating does not make an incorrectly sized filter suitable.
Match the model, dimensions and filter requirement first.
How often should a Santa Fe dehumidifier filter be checked?
Check the filter on a regular schedule and whenever airflow appears reduced. The QUNYI product information specifically says the Force and Advance 2 filter should be checked every 6 months.
Vacuuming may be suitable for some pleated filters, but disposable filters should be replaced as needed.
Can I use a Honeywell filter in a Santa Fe dehumidifier?
The CPLIKE filter identifies compatibility with Santa Fe Advance and Ultra models as well as Honeywell DR90 and DR120 units. That does not make every Honeywell filter suitable for every Santa Fe dehumidifier.
Match the dimensions and model compatibility before buying.
